Correct ifdef guards for HiFive1 demo_gpio

1 files changed, 25 insertions, 24 deletions

diff --git a/software/demo_gpio/demo_gpio.c b/software/demo_gpio/demo_gpio.c
index f568ae8..dec91b5 100644
--- a/software/demo_gpio/demo_gpio.c
+++ b/software/demo_gpio/demo_gpio.c
@@ -49,26 +49,26 @@ void handle_m_ext_interrupt(){
 void handle_m_time_interrupt(){
 
   clear_csr(mie, MIP_MTIP);
-  
+
   // Reset the timer for 3s in the future.
   // This also clears the existing timer interrupt.
-  
+
   volatile uint64_t * mtime       = (uint64_t*) (CLINT_BASE_ADDR + CLINT_MTIME);
   volatile uint64_t * mtimecmp    = (uint64_t*) (CLINT_BASE_ADDR + CLINT_MTIMECMP);
   uint64_t now = *mtime;
   uint64_t then = now + 1.5 * RTC_FREQUENCY;
   *mtimecmp = then;
- 
+
   // read the current value of the LEDS and invert them.
   uint32_t leds = *g_output_vals;
-  
+
   *g_output_vals ^= ((0x1 << RED_LED_OFFSET)   |
 		     (0x1 << GREEN_LED_OFFSET) |
 		     (0x1 << BLUE_LED_OFFSET));
-  
+
   // Re-enable the timer interrupt.
   set_csr(mie, MIP_MTIP);
-  
+
 }
 
 
@@ -105,18 +105,18 @@ Every 1.5 second, the Timer Interrupt will invert the LEDs.\n\
  ";
 
 void print_instructions() {
-  
+
   write (STDOUT_FILENO, instructions_msg, strlen(instructions_msg));
-  
+
 }
 
+#ifdef HAS_BOARD_BUTTONS
 void button_0_handler(void) {
 
   // Red LED on
   * g_output_vals |= (0x1 << RED_LED_OFFSET);
-		     
-  // Clear the GPIO Pending interrupt by writing 1.
 
+  // Clear the GPIO Pending interrupt by writing 1.
   GPIO_REG(GPIO_RISE_IP) = (0x1 << BUTTON_0_OFFSET);
 
 };
@@ -126,25 +126,26 @@ void button_1_handler(void) {
   // Green LED On
   * g_output_vals |= (1 << GREEN_LED_OFFSET);
 
+  // Clear the GPIO Pending interrupt by writing 1.
   GPIO_REG(GPIO_RISE_IP) = (0x1 << BUTTON_1_OFFSET);
-  
+
 };
 
- 
+
 void button_2_handler(void) {
 
   // Blue LED On
   * g_output_vals |= (1 << BLUE_LED_OFFSET);
 
   GPIO_REG(GPIO_RISE_IP) = (0x1 << BUTTON_2_OFFSET);
-  
-};
 
+};
+#endif
 
 void reset_demo (){
 
-    // Disable the machine & timer interrupts until setup is done.
-  
+  // Disable the machine & timer interrupts until setup is done.
+
   clear_csr(mie, MIP_MEIP);
   clear_csr(mie, MIP_MTIP);
 
@@ -157,7 +158,7 @@ void reset_demo (){
   g_ext_interrupt_handlers[INT_DEVICE_BUTTON_1] = button_1_handler;
   g_ext_interrupt_handlers[INT_DEVICE_BUTTON_2] = button_2_handler;
 #endif
-  
+
   print_instructions();
 
 #ifdef HAS_BOARD_BUTTONS
@@ -172,13 +173,13 @@ void reset_demo (){
   PLIC_set_priority(&g_plic, INT_DEVICE_BUTTON_0, 1);
   PLIC_set_priority(&g_plic, INT_DEVICE_BUTTON_1, 1);
   PLIC_set_priority(&g_plic, INT_DEVICE_BUTTON_2, 1);
-  
+
   GPIO_REG(GPIO_RISE_IE) |= (1 << BUTTON_0_OFFSET);
   GPIO_REG(GPIO_RISE_IE) |= (1 << BUTTON_1_OFFSET);
   GPIO_REG(GPIO_RISE_IE) |= (1 << BUTTON_2_OFFSET);
-  
+
 #endif
-  
+
     // Set the machine timer to go off in 3 seconds.
     // The
     volatile uint64_t * mtime       = (uint64_t*) (CLINT_BASE_ADDR + CLINT_MTIME);
@@ -186,13 +187,13 @@ void reset_demo (){
     uint64_t now = *mtime;
     uint64_t then = now + 1.5*RTC_FREQUENCY;
     *mtimecmp = then;
-    
+
     // Enable the Machine-External bit in MIE
     set_csr(mie, MIP_MEIP);
 
     // Enable the Machine-Timer bit in MIE
     set_csr(mie, MIP_MTIP);
-    
+
     // Enable interrupts in general.
     set_csr(mstatus, MSTATUS_MIE);
 }
@@ -207,7 +208,7 @@ int main(int argc, char **argv)
   * g_pullup_en  &= ~((0x1 << BUTTON_0_OFFSET) | (0x1 << BUTTON_1_OFFSET) | (0x1 << BUTTON_2_OFFSET));
   * g_input_en   |=  ((0x1 << BUTTON_0_OFFSET) | (0x1 << BUTTON_1_OFFSET) | (0x1 << BUTTON_2_OFFSET));
 #endif
-  
+
   * g_input_en    &= ~((0x1<< RED_LED_OFFSET) | (0x1<< GREEN_LED_OFFSET) | (0x1 << BLUE_LED_OFFSET)) ;
   * g_output_en   |=  ((0x1<< RED_LED_OFFSET)| (0x1<< GREEN_LED_OFFSET) | (0x1 << BLUE_LED_OFFSET)) ;
   * g_output_vals |=   (0x1 << BLUE_LED_OFFSET) ;
@@ -215,7 +216,7 @@ int main(int argc, char **argv)
 
   /**************************************************************************
    * Set up the PLIC
-   * 
+   *
    *************************************************************************/
   PLIC_init(&g_plic,
 	    PLIC_BASE_ADDR,