diff options
Diffstat (limited to 'software/clic_vectored')
| -rw-r--r-- | software/clic_vectored/clic_vectored.c | 65 |
1 files changed, 51 insertions, 14 deletions
diff --git a/software/clic_vectored/clic_vectored.c b/software/clic_vectored/clic_vectored.c index 6f19fa3..37ea723 100644 --- a/software/clic_vectored/clic_vectored.c +++ b/software/clic_vectored/clic_vectored.c @@ -28,13 +28,48 @@ clic_instance_t clic; const char * instructions_msg = " \ \n\ SiFive, Inc\n\ - E21 Core IP Eval Kit 'clic_vectored' demo.\n\ - This demo uses buttons 0, 1, and 2 on the\n\ - Arty board to trigger vectored clic interrupts.\n\ - The higher the button number, the higher the\n\ - interupt priority. Hold two buttons down at\n\ - the same time to see priorities in action.\n\ \n\ + 5555555555555555555555555\n\ + 5555 5555\n\ + 5555 5555\n\ + 5555 5555\n\ + 5555 5555555555555555555555\n\ + 5555 555555555555555555555555\n\ + 5555 5555\n\ + 5555 5555\n\ + 5555 5555\n\ +5555555555555555555555555555 55555\n\ + 55555 555555555 55555\n\ + 55555 55555 55555\n\ + 55555 5 55555\n\ + 55555 55555\n\ + 55555 55555\n\ + 55555 55555\n\ + 55555 55555\n\ + 55555 55555\n\ + 555555555\n\ + 55555\n\ + 5\n\ +\n\ +E2 Core IP Eval Kit 'clic_vectored' demo.\n\ +This demo uses buttons 0, 1, and 2 on the\n\ +Arty board to trigger vectored clic interrupts.\n\ +The higher the button number, the higher the\n\ +interupt priority. Button 0's handler runs for\n\ +10 seconds, button 1's for 5, and button 2's for 1.\n\ +Preemption is enabled so that higher priority\n\ +interrupts can be triggered while in low priority\n\ +handlers. The demo also uses the CLIC's software\n\ +interrupt to pend a lower priority interrupt from\n\ +button 2's handler.\n\ +\n\ +Note the buttons are wired directly into the local\n\ +interrupts, so a given interrupt will stay asserted\n\ +as long as the button is being pushed.\n\ +\n\ +This demo works for both the E20 and E21 FPGA\n\ +as long as CLIC_CONFIG_BITS matches the desired\n\ +core.\n\ \n"; void print_instructions() { @@ -50,13 +85,13 @@ void wait_ms(uint64_t ms) { while(*mtime<then); } -void button_0_isr(void) __attribute__((interrupt)); +void button_0_isr(void) __attribute__((interrupt("SiFive-CLIC-preemptible"))); void button_0_isr(void) { // Toggle Red LED uint8_t level = clic_get_int_level(&clic, (LOCALINTIDBASE + LOCAL_INT_BTN_0)); printf("Button 0 was pressed, interrupt level %d. Toggle Red.\n", level); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << RED_LED_OFFSET); - wait_ms(500); + wait_ms(10000); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << RED_LED_OFFSET); } @@ -66,13 +101,13 @@ void button_0_setup(void) { clic_enable_interrupt(&clic, (LOCALINTIDBASE + LOCAL_INT_BTN_0)); } -void button_1_isr(void) __attribute__((interrupt)); +void button_1_isr(void) __attribute__((interrupt("SiFive-CLIC-preemptible"))); void button_1_isr(void) { // Toggle Red LED uint8_t level = clic_get_int_level(&clic, (LOCALINTIDBASE + LOCAL_INT_BTN_1)); printf("Button 1 was pressed, interrupt level %d. Toggle Blue.\n", level); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << BLUE_LED_OFFSET); - wait_ms(500); + wait_ms(5000); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << BLUE_LED_OFFSET); } @@ -82,13 +117,15 @@ void button_1_setup(void) { clic_enable_interrupt(&clic, (LOCALINTIDBASE + LOCAL_INT_BTN_1)); } -void button_2_isr(void) __attribute__((interrupt)); +void button_2_isr(void) __attribute__((interrupt("SiFive-CLIC-preemptible"))); void button_2_isr(void) { // Toggle Red LED uint8_t level = clic_get_int_level(&clic, (LOCALINTIDBASE + LOCAL_INT_BTN_2)); - printf("Button 2 was pressed, interrupt level %d. Toggle Green.\n", level); + printf("Button 2 was pressed, interrupt level %d. Pending CSIPID and toggle Green.\n", level); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << GREEN_LED_OFFSET); - wait_ms(500); + //pend a software interrupt + clic_set_pending(&clic, CSIPID); + wait_ms(1000); GPIO_REG(GPIO_OUTPUT_VAL) = GPIO_REG(GPIO_OUTPUT_VAL) ^ (0x1 << GREEN_LED_OFFSET); } @@ -103,7 +140,7 @@ uint32_t COUNT; void csip_isr()__attribute((interrupt)); void csip_isr() { //clear the SW interrupt - clic_clear_pending(&clic, CSIPID); + CLIC0_REG8(CLIC_INTIP + CSIPID) = 0; COUNT++; } |