srcdir := $(dir $(realpath $(lastword $(MAKEFILE_LIST)))) srcdir := $(srcdir:/=) wrkdir := $(CURDIR)/work DEFAULT_BOARD := freedom-e300-hifive1 DEFAULT_PROGRAM := demo_gpio ############################################################# # Prints help message ############################################################# .PHONY: help help : @echo " SiFive Freedom E Software Development Kit " @echo " Makefile targets:" @echo "" @echo " tools:" @echo " Install compilation & debugging tools" @echo "" @echo " software [PROGRAM=$(DEFAULT_PROGRAM) BOARD=$(DEFAULT_BOARD)]:" @echo " Build a software program to load with the" @echo " debugger." @echo "" @echo " run_debug [PROGRAM=$(DEFAULT_PROGRAM) BOARD=$(DEFAULT_BOARD)]:" @echo " Launch OpenOCD & GDB to load or debug " @echo " running programs." @echo "" @echo " upload [PROGRAM=$(DEFAULT_PROGRAM) BOARD=$(DEFAULT_BOARD)]:" @echo " Launch OpenOCD to flash your program to the" @echo " on-board Flash" @echo "" @echo " run_openocd [BOARD=$(DEFAULT_BOARD)]:" @echo " run_gdb [PROGRAM=$(DEFAULT_PROGRAM) BOARD=$(DEFAULT_BOARD)]:" @echo " Launch OpenOCD or GDB seperately" @echo "" @echo " For more information, visit dev.sifive.com" ############################################################# # This section is for tool installation ############################################################# toolchain_srcdir := $(srcdir)/riscv-gnu-toolchain toolchain32_wrkdir := $(wrkdir)/riscv32-gnu-toolchain toolchain_dest := $(CURDIR)/toolchain PATH := $(toolchain_dest)/bin:$(PATH) openocd_srcdir := $(srcdir)/openocd openocd_wrkdir := $(wrkdir)/openocd openocd_dest := $(CURDIR)/toolchain target32 := riscv32-unknown-linux-gnu .PHONY: all all: tools @echo All done. tools: tools32 openocd @echo All Tools Installed tools32: $(toolchain_dest)/bin/$(target32)-gcc openocd: $(openocd_dest)/bin/openocd $(toolchain_dest)/bin/$(target32)-gcc: $(toolchain_srcdir) mkdir -p $(toolchain32_wrkdir) cd $(toolchain32_wrkdir); $(toolchain_srcdir)/configure --prefix=$(toolchain_dest) --with-arch=rv32imac --with-abi=ilp32 $(MAKE) -C $(toolchain32_wrkdir) $(openocd_dest)/bin/openocd: $(openocd_srcdir) mkdir -p $(openocd_wrkdir) cd $(openocd_srcdir); \ $(openocd_srcdir)/bootstrap cd $(openocd_wrkdir); \ $(openocd_srcdir)/configure --prefix=$(openocd_dest) $(MAKE) -C $(openocd_wrkdir) $(MAKE) -C $(openocd_wrkdir) install .PHONY: uninstall uninstall: rm -rf -- $(toolchain_dest) ############################################################# # This Section is for Software Compilation ############################################################# BOARD ?= $(DEFAULT_BOARD) PROGRAM ?= $(DEFAULT_PROGRAM) PROGRAM_DIR = $(srcdir)/software/$(PROGRAM) PROGRAM_ELF = $(srcdir)/software/$(PROGRAM)/$(PROGRAM) .PHONY: software software: cd $(PROGRAM_DIR);\ make software_clean: cd $(PROGRAM_DIR);\ make clean dasm: software cd $(PROGRAM_DIR); \ $(toolchain_dest)/bin/riscv32-unknown-elf-objdump -D $(PROGRAM_ELF) ############################################################# # This Section is for uploading a program to SPI Flash ############################################################# OPENOCD_UPLOAD = $(srcdir)/bsp/tools/openocd_upload.sh OPENOCDCFG ?= $(srcdir)/bsp/env/$(BOARD)/openocd.cfg upload: $(OPENOCD_UPLOAD) $(PROGRAM_ELF) $(OPENOCDCFG) ############################################################# # This Section is for launching the debugger ############################################################# OPENOCD = $(toolchain_dest)/bin/openocd OPENOCDARGS += -f $(OPENOCDCFG) GDB = $(toolchain_dest)/bin/riscv32-unknown-elf-gdb GDBCMDS += -ex "target extended-remote localhost:3333" GDBARGS = run_openocd: $(OPENOCD) $(OPENOCDARGS) run_gdb: $(GDB) $(PROGRAM_DIR)/$(PROGRAM) $(GDBARGS) run_debug: $(OPENOCD) $(OPENOCDARGS) & $(GDB) $(PROGRAM_DIR)/$(PROGRAM) $(GDBARGS) $(GDBCMDS) .PHONY: clean clean: rm -rf -- $(wrkdir)