blob: 41d01c0f862867f1b9b0c40259b268d1f044090b (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
RISCV ?= $(CURDIR)/toolchain
PATH := $(RISCV)/bin:$(PATH)
srcdir := $(dir $(realpath $(lastword $(MAKEFILE_LIST))))
srcdir := $(srcdir:/=)
wrkdir := $(CURDIR)/work
#############################################################
# Prints help message
#############################################################
.PHONY: help
help :
@echo " SiFive Freedom E Software Development Kit "
@echo " Makefile targets:"
@echo ""
@echo " tools:"
@echo " Install compilation & debugging tools"
@echo ""
@echo " software [PROGRAM=demo_gpio BOARD=freedom-e300-arty]:"
@echo " Build a software program to load with the"
@echo " debugger."
@echo ""
@echo " run_debug [PROGRAM=demo_gpio BOARD=freedom-e300-arty]:"
@echo " Launch OpenOCD & GDB to load or debug "
@echo " running programs."
@echo ""
@echo " upload [PROGRAM=demo_gpio BOARD=freedom-e300-arty]:"
@echo " Launch OpenOCD to flash your program to the"
@echo " on-board Flash"
@echo ""
@echo " run_openocd [BOARD=freedom-e300-arty]:"
@echo " run_gdb [PROGRAM=demo_gpio BOARD=freedom-e300-arty]:"
@echo " Launch OpenOCD or GDB seperately"
@echo ""
@echo " For more information, visit dev.sifive.com"
#############################################################
# This section is for tool installation
#############################################################
toolchain_srcdir := $(srcdir)/riscv-gnu-toolchain
toolchain32_wrkdir := $(wrkdir)/riscv32-gnu-toolchain
toolchain_dest := $(CURDIR)/toolchain
openocd_srcdir := $(srcdir)/openocd
openocd_wrkdir := $(wrkdir)/openocd
openocd_dest := $(CURDIR)/toolchain
target32 := riscv32-unknown-linux-gnu
.PHONY: all
all: tools
@echo All done.
tools: tools32 openocd
@echo All Tools Installed
tools32: $(toolchain_dest)/bin/$(target32)-gcc
openocd: $(openocd_dest)/bin/openocd
$(toolchain_dest)/bin/$(target32)-gcc: $(toolchain_srcdir)
mkdir -p $(toolchain32_wrkdir)
cd $(toolchain32_wrkdir); $(toolchain_srcdir)/configure --prefix=$(toolchain_dest) --with-arch=RV32IMA
$(MAKE) -C $(toolchain32_wrkdir)
$(openocd_dest)/bin/openocd: $(openocd_srcdir)
mkdir -p $(openocd_wrkdir)
cd $(openocd_srcdir); \
$(openocd_srcdir)/bootstrap
cd $(openocd_wrkdir); \
$(openocd_srcdir)/configure --prefix=$(openocd_dest)
$(MAKE) -C $(openocd_wrkdir)
$(MAKE) -C $(openocd_wrkdir) install
.PHONY: uninstall
uninstall:
rm -rf -- $(toolchain_dest)
#############################################################
# This Section is for Software Compilation
#############################################################
BOARD ?= freedom-e300-arty
PROGRAM ?= demo_gpio
PROGRAM_DIR = $(srcdir)/software/$(PROGRAM)
PROGRAM_ELF = $(srcdir)/software/$(PROGRAM)/$(PROGRAM)
.PHONY: software
software:
cd $(PROGRAM_DIR);\
make
software_clean:
cd $(PROGRAM_DIR);\
make clean
dasm: software
cd $(PROGRAM_DIR); \
$(toolchain_dest)/bin/riscv32-unknown-elf-objdump -D $(PROGRAM_ELF)
#############################################################
# This Section is for uploading a program to SPI Flash
#############################################################
OPENOCD_UPLOAD = $(srcdir)/bsp/tools/openocd_upload.sh
OPENOCDCFG ?= $(srcdir)/bsp/env/$(BOARD)/openocd.cfg
upload:
$(OPENOCD_UPLOAD) $(PROGRAM_ELF) $(OPENOCDCFG)
#############################################################
# This Section is for launching the debugger
#############################################################
OPENOCD = $(toolchain_dest)/bin/openocd
OPENOCDARGS += -f $(OPENOCDCFG)
GDB = $(toolchain_dest)/bin/riscv32-unknown-elf-gdb
GDBCMDS += -ex "target extended-remote localhost:3333"
GDBARGS =
run_openocd:
$(OPENOCD) $(OPENOCDARGS)
run_gdb:
$(GDB) $(PROGRAM_DIR)/$(PROGRAM) $(GDBARGS)
run_debug:
$(OPENOCD) $(OPENOCDARGS) &
$(GDB) $(PROGRAM_DIR)/$(PROGRAM) $(GDBARGS) $(GDBCMDS)
.PHONY: clean
clean:
rm -rf -- $(wrkdir)
|
